IMPROVING SILK REELING EQUIPMENT TO OBTAIN HIGH-QUALITY RAW SILK FROM LOCAL SILKWORM COCOONS
- Authors
-
-
Ulug‘bek Akhunbabayev
PhD, Senior Researcher, Head of the Laboratory, Uzbek Scientific Research Institute of Natural Fibers, Margilon, Uzbekistan -
Fotimabonu Rustamova
PhD candidate, Namangan State Technical University, Uzbekistan -
Akmal Umarov
DSc, Associate Professor of the Department of Technological Machinery and Equipment, Namangan State Technical University, Namangan, Uzbekistan
-
- Keywords:
- silk reeling raw silk Bombyx mori local cocoons process control PID reelability fineness uniformity gear reducer kinematic scheme
- Abstract
- The quality of raw silk is determined jointly by the intrinsic properties of the cocoon and by the mechanical and thermal environment in which the filament is unwound. Local cocoon hybrids frequently show high intrinsic potential, yet raw silk reeled on ageing, mostly mechanically controlled equipment is often downgraded because of fineness variation, frequent filament breakage and elevated cleanness defects. This study presents the design, implementation and experimental evaluation of an integrated set of seven equipment improvements: cocoon sorting, staged three-zone cooking, closed-loop reeling-basin temperature control, ceramic eyelets with an optimized cross-twist unit, a photoelectric fineness sensor with automatic cocoon feeding, a load-cell based adaptive take-up, and humidity-controlled drying. The modifications were driven by a PLC-based PID controller with data logging. The structural and kinematic schemes of the improved reeling unit are presented, and its reel drive, consisting of an asynchronous motor with a frequency converter, a V-belt drive and a two-stage cylindrical gear reducer, is calculated so that the reeling speed can be set within 36-84 m/min. Five lots of locally produced cocoons were reeled to 20/22 den raw silk on a baseline machine and on the improved machine, with three replicates per lot. The improved configuration raised reelability from 71.2 % to 86.4 %, increased raw silk recovery from 34.9 % to 39.6 %, reduced the coefficient of variation of fineness from 14.2 % to 7.8 %, lowered the filament break rate by 58 %, and improved tenacity by 14.3 %, moving the product from an intermediate grade to the top commercial grade. Specific thermal energy consumption decreased by 29 %. The results show that targeted, low-cost equipment upgrades can unlock the quality potential of local cocoons without changing the raw material, and they provide design rules that can be transferred to small and medium reeling enterprises.
- References
-
[1] C. Holland, K. Numata, J. Rnjak-Kovacina, and F. P. Seib, “The biomedical use of silk: Past, present, future,” Adv. Healthcare Mater., vol. 8, no. 1, Art. no. 1800465, 2019.
[2] D. N. Rockwood, R. C. Preda, T. Yücel, X. Wang, M. L. Lovett, and D. L. Kaplan, “Materials fabrication from Bombyx mori silk fibroin,” Nature Protocols, vol. 6, no. 10, pp. 1612–1631, 2011.
[3] F. Vollrath and D. P. Knight, “Liquid crystalline spinning of spider silk,” Nature, vol. 410, no. 6828, pp. 541–548, 2001.
[4] Z. Shao and F. Vollrath, “Surprising strength of silkworm silk,” Nature, vol. 418, no. 6899, p. 741, 2002.
[5] H.-J. Jin and D. L. Kaplan, “Mechanism of silk processing in insects and spiders,” Nature, vol. 424, no. 6952, pp. 1057–1061, 2003.
[6] Y.-Q. Zhang, “Applications of natural silk protein sericin in biomaterials,” Biotechnol. Adv., vol. 20, no. 2, pp. 91–100, 2002.
[7] J. G. Hardy, L. M. Römer, and T. R. Scheibel, “Polymeric materials based on silk proteins,” Polymer, vol. 49, no. 20, pp. 4309–4327, 2008.
[8] M. Mondal, K. Trivedy, and S. Nirmal Kumar, “The silk proteins, sericin and fibroin in silkworm, Bombyx mori Linn.—a review,” Caspian J. Environ. Sci., vol. 5, no. 2, pp. 63–76, 2007.
[9] K. M. Babu, Silk: Processing, Properties and Applications. Cambridge, U.K.: Woodhead Publishing, 2013.
[10] G. H. Altman, F. Diaz, C. Jakuba, T. Calabro, R. L. Horan, J. Chen, H. Lu, J. Richmond, and D. L. Kaplan, “Silk-based biomaterials,” Biomaterials, vol. 24, no. 3, pp. 401–416, 2003.
[11] C. Vepari and D. L. Kaplan, “Silk as a biomaterial,” Prog. Polym. Sci., vol. 32, no. 8–9, pp. 991–1007, 2007.
[12] T. D. Sutherland, J. H. Young, S. Weisman, C. Y. Hayashi, and D. J. Merritt, “Insect silk: One name, many materials,” Annu. Rev. Entomol., vol. 55, pp. 171–188, 2010.
[13] F. G. Omenetto and D. L. Kaplan, “New opportunities for an ancient material,” Science, vol. 329, no. 5991, pp. 528–531, 2010.
[14] H.-P. Zhao, X.-Q. Feng, and H.-J. Shi, “Variability in mechanical properties of Bombyx mori silk,” Mater. Sci. Eng. C, vol. 27, no. 4, pp. 675–683, 2007.
[15] F. Chen, D. Porter, and F. Vollrath, “Structure and physical properties of silkworm cocoons,” J. R. Soc. Interface, vol. 9, no. 75, pp. 2299–2308, 2012.
[16] C.-Z. Zhou, F. Confalonieri, N. Medina, Y. Zivanovic, C. Esnault, T. Yang, M. Jacquet, J. Janin, M. Duguet, R. Perasso, and Z.-G. Li, “Fine organization of Bombyx mori fibroin heavy chain gene,” Nucleic Acids Res., vol. 28, no. 12, pp. 2413–2419, 2000.
[17] Y. F. Lee, Silk Reeling and Testing Manual, FAO Agricultural Services Bulletin 136. Rome, Italy: Food and Agriculture Organization of the United Nations, 1999.
[18] B. Kundu, R. Rajkhowa, S. C. Kundu, and X. Wang, “Silk fibroin biomaterials for tissue regenerations,” Adv. Drug Deliv. Rev., vol. 65, no. 4, pp. 457–470, 2013.
[19] F. Rustamova, S. Dadajonov, and U. B. Akhunbabayev, “From local silkworm seeds achievement processed fine-fiber cocoons processing of low-linear density raw silk release technology,” Oscar Journal of Applied Science and Technology, vol. 5, no. 12, pp. 147–151, 2025.